How to Optimize Ventilation in Mines Using Diesel Equipment?

🔹 Problem: Modern mines utilize high-power diesel equipment, significantly increasing ventilation load. Traditional airflow calculation methods overestimate requirements by 50%, leading to substantial costs.

🔹 Solution: Researchers developed a novel methodology based on field measurements of actual emissions and numerical simulation. This enables precise determination of airflow needed to dilute harmful substances to safe concentrations.

🔹 Key Results:
✅ Reduced ventilation costs through accurate emission accounting
✅ Optimized air distribution in mine workings
✅ 3.5× decrease in CO and NO₂ concentrations with proper ventilation

For more information, see the article:

📌 Senatorov V.A. Determining airflow requirements in mine workings based on field measurements of actual emissions from internal combustion engine equipment. Mining Science and Technology (Russia). 2024;9(1):53-59. https://doi.org/10.17073/2500-0632-2024-01-203

💡 Conclusion: Innovative calculation methods represent a breakthrough in cost efficiency and environmental safety for mining operations!

Subscribe to our Telegram channel:
👉 t.iss.one/MinSciTech 👈

#InEnglish #MST #mining #ventilation #diesel #exhaustgases #numericalsimulation #safety #undergroundmining #ICE #aerodynamics #fieldmeasurements #concentration #CO #NOx #MAC #standards #optimization #costreduction #energyefficiency #technology #digitalization #monitoring #mineatmosphere #workings #aircontrol #hazardoussubstances #filtration #temperature #pressure #humidity #analysis #equipment #efficiency #research #methodology #calculation #dynamics #operationmode #load #results #implementation #practicalapplication

We present the articles of the first issue of scientific journal "Mining Science and Technology” (Russia) for 2025:

Scientists conducting research at the mines of the VVerkhnekamsk potassium-magnesium salt deposit (VPMSD) discovered an interesting pattern: gas-air surveys show that the volume of gaseous impurities in the main ventilation drifts is often significantly lower than in the working areas of dead-end workings. This phenomenon of decreasing gas concentrations along the ventilation airflow path is explained not only by the dilution of impurities due to fresh air leaks but also by the chemical neutralization of gases through interaction with the potash rock mass. Previously conducted laboratory studies confirmed the ability of sylvinite (NaCl + KCl) to absorb toxic and combustible gases. This paper presents the results of field studies at one of the VPMSD mines, where the dynamics of gas impurities in the workings were studied, taking into account both chemical processes and ventilation factors. Specialists measured the concentration of combustible and toxic gases in seams of different mineral compositions and analyzed the influence of potash salt properties on the gas composition in long dead-end workings. Laboratory analysis of the collected air samples, performed by chromatographic method using the "CHROMOS GH-1000" instrument, made it possible to quantitatively assess the contribution of gas neutralization and dilution processes to the reduction of harmful impurity concentrations. The results showed that in long dead-end workings of seam AB (100 m or more), the content of gaseous impurities consistently decreases as the distance from the dead end to the mouth of the working increases. The study also examined other factors influencing changes in the gas composition in mine workings.

For more information, see the article:

📌 Starikov A.N., Maltsev S.V., Sukhanov A.E. Influence of the sorption properties of potash salts on the gas environment in dead-end mine workings. Mining Science and Technology (Russia). 2025;10(1):25-33. https://doi.org/10.17073/2500-0632-2024-01-210

Subscribe to our Telegram channel:
👉 t.iss.one/MinSciTech 👈

#InEnglish #MST #mine #gas #sorption #leaks #sylvinite #methane #CO #CO2 #H2S #ventilation #shaft #safety #chemistry #science #mining #analysis #experiment #laboratory #air #seam #measurement #point #length #path #jet #face #mouth #volume #harm #risk #standard #method #device #data #result #experience #salt #KCl #NaCl #zone #deadend #tube #speed #pressure #balance #neutralization

How to Improve Block Stone Quality with Blasting Technology?

The extraction of block stone is a critical process in the construction materials industry, where maintaining the integrity of the material for further use is paramount. The key challenge lies in minimizing induced fracturing and surface roughness of the blocks.

🔹 Key Aspects of the Technology:
✔️ Stress wave interaction – plays a decisive role in forming the main rupture between blastholes.
✔️ Optimal charge parameters – blasthole spacing, blast product pressure, and linear charge density influence the zone of induced fracturing.
✔️ Orientation of the rupture plane – aligning it with natural fractures in the rock mass increases the yield of high-quality blocks.

🔹 Research Findings:
✔️Numerical modeling confirmed that adjusting charge parameters localizes the fracture zone.
✔️Reducing blasthole spacing while increasing charge size within limits ensures directional splitting.

For more information, see the article:

📌 Kovalevsky V.N., Mysin A.V., Sushkova V.I. Theoretical aspects of block stone blasting method. Mining Science and Technology (Russia). 2024;9(2):97-104. https://doi.org/10.17073/2500-0632-2023-12-187

Subscribe to our Telegram channel:
👉 t.iss.one/MinSciTech 👈

#InEnglish #MST #BlockRockMass #DrillingAndBlasting #DirectedFlow #ChargeDesign #BlastPulse #BlastPressure #StressDiagrams #DynamicStrength #Roughness #InducedFracturing #Stone #Blast #Charge #Mass #Cracks #Rock #Pressure #Strength #Granite #Tech