Club Arduino 💡🪛🧲

Тензометрические датчики на 1-10 кг , а так же плата преобразователь АЦП HX711 AD для сборки весов.
US $4.18
https://ali.pub/5hyin9

Весы на ардуино :

#include "HX711.h"

HX711 scale;

void setup() {
Serial.begin(38400);
Serial.println("HX711 Demo");

Serial.println("Initializing the scale");
// parameter "gain" is ommited; the default value 128 is used by the library
// HX711.DOUT - pin #A1
// HX711.PD_SCK - pin #A0
scale.begin(3, 2);

Serial.println("Before setting up the scale:");
Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight (not set yet)

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight (not set) divided
// by the SCALE parameter (not set yet)

scale.set_scale(994.68); // this value is obtained by calibrating the scale with known weights; see the README for details
scale.tare(); // reset the scale to 0

Serial.println("After setting up the scale:");

Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight, set with tare()

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight, divided
// by the SCALE parameter set with set_scale

Serial.println("Readings:");
}

void loop() {
Serial.print("one reading:\t");
Serial.print(scale.get_units(), 1);
Serial.print("\t| average:\t");
Serial.println(scale.get_units(10), 1);

scale.power_down(); // put the ADC in sleep mode
delay(5000);
scale.power_up();
}

aliexpress.com

4.18US $ 10% OFF|Digital Load Cell Weight Sensor HX711 AD Converter Breakout Module 5KG 10KG Portable Electronic Kitchen Scale…

Smarter Shopping, Better Living! Aliexpress.com

319 views07:06

Club Arduino 💡🪛🧲

aliexpress.com

4.18US $ 10% OFF|Digital Load Cell Weight Sensor HX711 AD Converter Breakout Module 5KG 10KG Portable Electronic Kitchen Scale…

Smarter Shopping, Better Living! Aliexpress.com

259 views20:01

Club Arduino 💡🪛🧲

Тензометрические датчики на 1-10 кг , а так же плата преобразователь АЦП HX711 AD для сборки весов.
US $4.18
https://aliclick.shop/r/c/1r394cm6octwuus9?product_id=4000272063976

Весы на ардуино :

#include "HX711.h"

HX711 scale;

void setup() {
Serial.begin(38400);
Serial.println("HX711 Demo");

Serial.println("Initializing the scale");
// parameter "gain" is ommited; the default value 128 is used by the library
// HX711.DOUT - pin #A1
// HX711.PD_SCK - pin #A0
scale.begin(3, 2);

Serial.println("Before setting up the scale:");
Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight (not set yet)

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight (not set) divided
// by the SCALE parameter (not set yet)

scale.set_scale(994.68); // this value is obtained by calibrating the scale with known weights; see the README for details
scale.tare(); // reset the scale to 0

Serial.println("After setting up the scale:");

Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight, set with tare()

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight, divided
// by the SCALE parameter set with set_scale

Serial.println("Readings:");
}

void loop() {
Serial.print("one reading:\t");
Serial.print(scale.get_units(), 1);
Serial.print("\t| average:\t");
Serial.println(scale.get_units(10), 1);

scale.power_down(); // put the ADC in sleep mode
delay(5000);
scale.power_up();
}
https://aliclick.shop/r/c/1r394cm6octwuus9?product_id=4000272063976&from_content=wall_-107877557_127103&gaid=bfc0fd12-544f-4bc8-96c7-c6e5f5a06353&sns_params=%7B%22vk_id%22%3A10943591%2C%22exps%22%3A%5B%5D%7D

216 views13:06

Club Arduino 💡🪛🧲

Тензометрические датчики на 1-10 кг , а так же плата преобразователь АЦП HX711 AD для сборки весов.
US $4.18
https://aliclick.shop/r/c/1r394cm6octwuus9?product_id=4000272063976

Весы на ардуино :

#include "HX711.h"

HX711 scale;

void setup() {
Serial.begin(38400);
Serial.println("HX711 Demo");

Serial.println("Initializing the scale");
// parameter "gain" is ommited; the default value 128 is used by the library
// HX711.DOUT - pin #A1
// HX711.PD_SCK - pin #A0
scale.begin(3, 2);

Serial.println("Before setting up the scale:");
Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight (not set yet)

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight (not set) divided
// by the SCALE parameter (not set yet)

scale.set_scale(994.68); // this value is obtained by calibrating the scale with known weights; see the README for details
scale.tare(); // reset the scale to 0

Serial.println("After setting up the scale:");

Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight, set with tare()

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight, divided
// by the SCALE parameter set with set_scale

Serial.println("Readings:");
}

void loop() {
Serial.print("one reading:\t");
Serial.print(scale.get_units(), 1);
Serial.print("\t| average:\t");
Serial.println(scale.get_units(10), 1);

scale.power_down(); // put the ADC in sleep mode
delay(5000);
scale.power_up();
}
https://aliclick.shop/r/c/1r394cm6octwuus9?product_id=4000272063976&from_content=wall_-43363264_522391&gaid=bfc0fd12-544f-4bc8-96c7-c6e5f5a06353&sns_params=%7B%22vk_id%22%3A10943591%2C%22exps%22%3A%5B%5D%7D

287 views12:01

Club Arduino 💡🪛🧲

Тензометрические датчики на 1-10 кг , а так же плата преобразователь АЦП HX711 AD для сборки весов.
US $4.18
https://aliclick.shop/r/c/1r394cm6octwuus9?product_id=4000272063976

Весы на ардуино :

#include "HX711.h"

HX711 scale;

void setup() {
Serial.begin(38400);
Serial.println("HX711 Demo");

Serial.println("Initializing the scale");
// parameter "gain" is ommited; the default value 128 is used by the library
// HX711.DOUT - pin #A1
// HX711.PD_SCK - pin #A0
scale.begin(3, 2);

Serial.println("Before setting up the scale:");
Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight (not set yet)

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight (not set) divided
// by the SCALE parameter (not set yet)

scale.set_scale(994.68); // this value is obtained by calibrating the scale with known weights; see the README for details
scale.tare(); // reset the scale to 0

Serial.println("After setting up the scale:");

Serial.print("read: \t\t");
Serial.println(scale.read()); // print a raw reading from the ADC

Serial.print("read average: \t\t");
Serial.println(scale.read_average(20)); // print the average of 20 readings from the ADC

Serial.print("get value: \t\t");
Serial.println(scale.get_value(5)); // print the average of 5 readings from the ADC minus the tare weight, set with tare()

Serial.print("get units: \t\t");
Serial.println(scale.get_units(5), 1); // print the average of 5 readings from the ADC minus tare weight, divided
// by the SCALE parameter set with set_scale

Serial.println("Readings:");
}

void loop() {
Serial.print("one reading:\t");
Serial.print(scale.get_units(), 1);
Serial.print("\t| average:\t");
Serial.println(scale.get_units(10), 1);

scale.power_down(); // put the ADC in sleep mode
delay(5000);
scale.power_up();
}
https://aliclick.shop/r/c/1r394cm6octwuus9?product_id=4000272063976&from_content=wall_-43363264_566104&gaid=bfc0fd12-544f-4bc8-96c7-c6e5f5a06353&sns_params=%7B%22vk_id%22%3A10943591%2C%22exps%22%3A%5B%5D%7D

416 viewsAli_radio, 01:38

About

Blog

Apps

Platform